BMW 1-Series Forum (F20) 135i - 1Addicts.com > Second Generation 1 Series Forum > DIY Guides and Instructions > water pump N13, 2021
Post Reply
 
Thread Tools Search this Thread
      11-10-2021, 02:23 AM   #1
mbaki
Registered
0
Rep
2
Posts

Drives: bmw 118i 2013 model f20
Join Date: Dec 2018
Location: gaborone, botswana

iTrader: (0)

water pump N13, 2021

Good day good people, any anyone with DIY STEPS for replacing water pump bmw f20 118i n13 model.

thanks
Appreciate 0
      11-10-2021, 05:16 AM   #2
stupar
New Member
0
Rep
12
Posts

Drives: BMW F20
Join Date: May 2021
Location: Bosnia and Herzegowina

iTrader: (0)

This one is for aux coolant pump:

https://www.bimmerforums.co.uk/threa...mp-diy.561719/

Maybe this one can help with water pump:

https://www.highliftmedia.com/bmw-1-...acement-guide/
Appreciate 0
      11-26-2021, 10:49 AM   #3
pigboy
Registered
0
Rep
4
Posts

Drives: 116i F20
Join Date: Nov 2021
Location: Yorkshire

iTrader: (0)

I did this a little while back on my 116i and from a quick search on RealOEM it looks like it might be the same process/parts for you:

https://www.realoem.com/bmw/enUS/sho...diagId=11_5011

I don't have a guide as such, I just used the diagram on the realoem link to help find the pump location and part number for a replacement. Here are a few steps off the top of my head (assuming you've drained your coolant):
  • Disconnect air hoses and remove the airbox for easier access to the engine bay
  • Locate the water pump drive wheel (bottom left of the engine, see photos)
  • Remove the drive wheel from the pump by taking out the 3 screws (worth replacing this at the same time. I didn't and had to within 2 weeks)
  • Remove the 5 screws holding the waterpump in
  • Put the new waterpump in palce, add some threadlocker (I used medium strength) to the bolts and hand tighten (do not overtighten these bolts, they are quick to crossthread). Think I might've torqued to 10nm, but it's probably not needed
  • Put your (preferably new) drive wheel on the front of the pump - this is a bit of a pain but with some shoving and moving it gets there. You can then use a driver/pencil to line up the holes of the drive wheel with the holes on the pump
  • Put some threadlocker (again I used medium strength) on the drive wheel bolts and hand tighten. Again, they're a bit of a pain when it comes to crossthreading

Engine Bay:
Name:  IMG_2091 2.jpg
Views: 11
Size:  524.4 KB

Engine Bay with airbox removed and waterpump drivewheel located:
Name:  IMG_2034.jpg
Views: 10
Size:  422.4 KB

Waterpump drivewheel (you can see the cuts in the rubber on mine, which is why I had to replace it):
Name:  IMG_2035.jpg
Views: 9
Size:  578.0 KB

Hope it helps!
Appreciate 0
Post Reply

Bookmarks

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off



All times are GMT -5. The time now is 06:21 PM.




1addicts
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2021, vBulletin Solutions Inc.
1Addicts.com, BIMMERPOST.com, E90Post.com, F30Post.com, M3Post.com, ZPost.com, 5Post.com, 6Post.com, 7Post.com, XBimmers.com logo and trademark are properties of BIMMERPOST