BMW 1-Series Forum (F20) 135i - 1Addicts.com > Second Generation 1 Series Forum > DIY Guides and Instructions > M Buttons Sports Eco Mode Mod
Post Reply
 
Thread Tools Search this Thread
      12-31-2020, 11:07 PM   #1
RJ019
Private First Class
Australia
90
Rep
110
Posts

Drives: 2009 135i Low Mount ST
Join Date: May 2017
Location: ACT

iTrader: (0)

I changed my blank buttons to M buttons and made them function as the Sport and Eco mode buttons. This is not a step by step DIY but will give you a good idea how to attempt it if you want to at your own risk. This took me about a day to work out from start to finish and only cost me $30 for the genuine M buttons which I got off someone with an M2 who changed to the coloured versions. The rest of the parts I had lying around so were not at an additional cost to me.

This was done by running a harness from the switch in the centre console to the steering wheel through the clockspring. My car has a single stage airbag so only had two wires through the clockspring this means there are 4 pins not used for that particular connector.

Name:  1.1.jpg
Views: 4982
Size:  221.0 KB

Name:  1.2.jpg
Views: 3631
Size:  356.0 KB

Name:  2.jpg
Views: 4111
Size:  181.4 KB

The blank buttons have these tabs that stops the button from being pressed in on the M buttons these are flush.

Name:  3.1.jpg
Views: 3567
Size:  397.9 KB

If the airbag connector only has two wires then you can do this mod. If you have a two stage airbag this will probably have 4 wires so there will only be two spare pins you will need 3. You may be able to find another spare pin on another connector which you will need to work out what the corresponding pin/wire is on the other side of the clockspring with the use of a multimeter.

Name:  4.jpg
Views: 3861
Size:  327.9 KB

Name:  5.jpg
Views: 3513
Size:  147.3 KB

On the connector on the back of the clockspring I used pins 1-3 the corresponding numbers on the airbag connector are 4-6. I ran a harness around the steering wheel shaft and back down and on the side of the center console up to the Sport - Eco switch.

Name:  6.jpg
Views: 3542
Size:  389.5 KB

Name:  7.1.jpg
Views: 3573
Size:  144.7 KB

Name:  7.2.jpg
Views: 3518
Size:  323.7 KB

Name:  8.jpg
Views: 3488
Size:  178.5 KB

Name:  9.1.jpg
Views: 3530
Size:  219.8 KB

Name:  9.2.jpg
Views: 3541
Size:  269.2 KB

I had an old spare N54 wiring harness I have been hacking up for my various projects this is where I got my pin connectors and wires. If you have removed the the mobile phone unit in your car you may be able to use this connector but I can not confirm if this will actually work as I have not checked the size. So you will need to check for yourself or you will need to purchase some connectors.

Name:  11.jpg
Views: 3617
Size:  649.5 KB

Name:  12.jpg
Views: 3501
Size:  133.9 KB

Name:  13.jpg
Views: 3534
Size:  272.1 KB

Name:  14.jpg
Views: 3536
Size:  337.0 KB

Name:  15.jpg
Views: 3508
Size:  449.4 KB

Remove the Sport and Eco switch from the centre console and pulled it apart I then soldered 2 wires B & C onto the circuit board and ran the wires out the bottom where there were already two small holes and joined to the harness I ran from the steering wheel.

Name:  16.jpg
Views: 3727
Size:  184.5 KB

Name:  17.jpg
Views: 3523
Size:  207.4 KB

Name:  18.jpg
Views: 3499
Size:  196.0 KB

I then tapped the last wire from the harness into the brown and white wire on the connector which is A for the circuit and the common wire for the Sport and Eco switch.

Name:  19.jpg
Views: 3503
Size:  161.7 KB

Pull the steering wheel switch apart as you can see it is missing LEDs for the M buttons you will need to solder some in and resistors for both of them.

For my M1 and M2 buttons I utilized the original switches on the circuit board this is a bit difficult and requires modifying the circuit board traces etc and unfortunate I did not take any pictures of my final version as I was too focused on getting it to work. I would not recommend this route for most people unless you know what you are doing as you can easily damage your board. Essentially you will need to isolate the M1 and M2 switches from the rest of the circuit as it will interfere with the LIN signals and make functions like speed limit go off when you don't want them too.

What I would recommend is getting some switched similar to these and just have then placed on top of the original switch with some thin wires. I drilled a hole out the back of the switch to run the 3 wires to the airbag connector.

https://www.digikey.com.au/product-d...70401#images-3

Name:  20.1.jpg
Views: 3470
Size:  356.0 KB

Name:  20.2.jpg
Views: 3493
Size:  217.2 KB

Name:  22.jpg
Views: 3505
Size:  324.5 KB

Name:  24.jpg
Views: 3494
Size:  131.1 KB

Name:  25.jpg
Views: 3481
Size:  130.8 KB

Name:  26.jpg
Views: 3472
Size:  225.1 KB
Ray J

Last edited by RJ019; 01-01-2021 at 12:17 AM..
Appreciate 2
      02-03-2021, 06:24 PM   #2
sam_293839
Registered
0
Rep
2
Posts

Drives: BMW M135i 2014
Join Date: Nov 2020
Location: NE

iTrader: (0)

This is awesome, fair play. Do you know what the resistor and LED sizes are? Also do you know the exact colour of the original orange LEDs?
Appreciate 0
      05-27-2021, 10:59 AM   #3
F20_M135i
Lieutenant
France
101
Rep
551
Posts

Drives: BMW F20 M140i Xdrive
Join Date: Mar 2020
Location: FRANCE

iTrader: (0)

man you are a genius
Appreciate 0
      08-20-2021, 04:18 PM   #4
King_Tubby
New Member
United Kingdom
0
Rep
5
Posts

Drives: BMW 118i
Join Date: Jul 2021
Location: UK

iTrader: (0)

Brilliant explanation and photos. Inspirational!!
Appreciate 0
      08-29-2021, 10:20 AM   #5
nivanikov
New Member
Germany
0
Rep
7
Posts

Drives: BMW 1er, 3er
Join Date: Aug 2021
Location: Germany

iTrader: (0)

Super detail, thanks
Appreciate 0
      11-30-2021, 04:27 PM   #6
J25LY
New Member
United Kingdom
2
Rep
6
Posts

Drives: M135i EWG
Join Date: Nov 2021
Location: UK

iTrader: (0)

Fair play to you fella, would you say this is worth doing?
Appreciate 0
      12-27-2021, 02:21 PM   #7
Mirco1994
Registered
0
Rep
2
Posts

Drives: 320 e90
Join Date: May 2018
Location: Italia

iTrader: (0)

Do you know what the resistor and LED sizes are? Also do you know the exact color of the original orange Or White led ?
I talking about the led of F20 m sport steering wheel
Thanks
Appreciate 0
Post Reply

Bookmarks


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off



All times are GMT -5. The time now is 12:27 PM.




1addicts
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
1Addicts.com, BIMMERPOST.com, E90Post.com, F30Post.com, M3Post.com, ZPost.com, 5Post.com, 6Post.com, 7Post.com, XBimmers.com logo and trademark are properties of BIMMERPOST